浅海混响的建模与预报

建立了独立于传播模型之外的统一的浅海混响计算模型,分别给出基于简正波理论和波束跟踪理论的模型表达式.结合仿真算例和实验数据,进行了基于这两种理论的模型计算结果比较分析和实验验证.结果表明,统一的混响计算模型有利于基于不同的传播模型进行混响强度的计算,且具有明晰的物理意义;基于简正波理论与波束跟踪理论的模型计算结果吻合,使用这两种方法都能很好地预报实验结果.     

函数变换提高灰色预测模型精度的条件

指出选择函数变换来提高模型精度主要与三个方面的因素有关：提高数据序列的光滑比、调整数据序列的级比和确保凸凹性。在调整级比方面，扩充了级比压缩变换的相关定理，并讨论了几种常用的函数变换在上述三个方面的关系。最后结合实例提出，对于变换后的数据序列若不满足这三方面的要求可以再进行函数变换以达到提高模型精度的目的。     

两种捆绑火箭弹性振动建模方法对比分析及其对姿控系统的影响

针对长助推和短助推两种类型捆绑火箭的不同模态特点,分析了两者弹性振动建模方法的区别和联系,在此基础上建立了某型固体捆绑火箭姿态动力学新模型,模型中基于有限元法导出了弹性振动方程,基于该模型对箭体复杂弹性振动引起的通道间耦合进行了研究,采用逆Nyquist阵列法进行设计。结果表明,该模型能更准确地反映捆绑火箭纵、横、扭耦合运动特性;新模型三通道之间存在弹性耦合,但耦合矩阵具有对角优势性质,采用逆Nyquist阵列法进行姿控系统设计是有效的,仿真结果表明设计的控制器可行,能够取得比较好的性能。     

应用改进的LP算法构建虚拟阵的精确定向方法

为了克服传统LP(Linear Predecition)算法在构建虚拟阵过程中存在预测误差容易累积的弊端,提出了一种能够更充分利用实阵信息量的改进LP算法来构建虚拟阵。采用实际基阵方法、传统LP虚拟阵方法和改进LP虚拟阵方法分别对假定基阵的波束性能进行计算机仿真及对湖试数据进行处理成像,研究结果表明,与传统LP方法相比,改进的LP方法能够有效地抑制波束旁瓣,进一步提高了基阵的角度分辨力和阵增益,将其运用于特定试验背景下的实际湖底目标探测,方向分辨精度可提高75%。     

多全球导航卫星系统联合的探月飞行器轨道定位分析

针对探月飞行器月球公转轨道上的卫星导航定位问题,以高轨道飞行器卫星导航定位的研究为基础,采用多全球导航卫星系统联合定位的方法进行仿真。分析了载波功率与噪声功率密度比为15d BHz的弱信号捕获门限下,各系统联合定位时波束主瓣和旁瓣的可用性,同时对各系统联合情况下的精度因子值进行分析。仿真结果表明:当接收到的卫星天线辐射的主瓣和旁瓣信号均高于载噪比门限时,全球导航卫星系统的三系统或四系统的联合能满足实时定位条件;而旁瓣损耗不加以补偿时,接收信号载噪比低于门限并导致任意联合方式均无法完成定位。各系统联合的精度因子分析表明:单系统或双系统联合的几何精度因子变化剧烈,四系统联合相比三系统联合的几何精度因子下降16.93%;三系统联合定位方案中,美国全球定位系统、中国的北斗卫星导航定位系统与欧洲的伽利略卫星导航定位系统联合方案的几何精度因子值变化最平稳,为最佳选择。理论分析和仿真结果为探月飞行器定位技术研究和星载多系统接收机设计提供参考。     

Driving force coordinated control of an 8 ×8 in-wheel motor drive vehicle with tire-road friction coefficient identification

Because of the complexities of tire-road interaction,the wheels of a multi-wheel distributed electric drive vehicle can easily slip under certain working conditions.As wheel slip affects the dynamic per-formance and stability of the vehicle,it is crucial to control it and coordinate the driving force.With this aim,this paper presents a driving force coordination control strategy with road identification for eight-wheeled electric vehicles equipped with an in-wheel motor for each wheel.In the proposed control strategy,the road identification module estimates tire-road forces using an unscented Kalman filter al-gorithm and recognizes the road adhesion coefficient by employing the recursive least-square method.According to road identification,the optimal slip ratio under the current driving condition is obtained,and a controller based on sliding mode control with a conditional integrator uses this value for accel-eration slip regulation.The anti-slip controller obtains the adjusting torque,which is integrated with the driver-command-based feedforward control torque to implement driving force coordination control.The results of hardware-in-loop simulation show that this control strategy can accurately estimate tire-road forces as well as the friction coefficient,and thus,can effectively fulfill the purpose of driving force coordinated control under different driving conditions.     

预应力CFRP筋T形梁受弯性能试验及变形分析

试验通过对3根T形预应力CFRP筋混凝土梁和1根矩形预应力CFRP筋混凝土梁进行对比,考察了预应力CFRP筋混凝土梁的受弯工作性能,记录了试验梁的开裂荷载、极限荷载和裂缝发展情况。试验结果表明：增加预应力度和总配筋率对提高开裂荷载,限制挠度、裂缝发展起重要作用;相同配筋的T形梁和矩形梁挠度相近,但各阶段荷载不同。对预应力CFRP筋T形梁的变形性能进行了理论分析,推导了短期荷载作用下刚度和挠度的计算公式,并将计算值与试验值进行比较,两者吻合良好。     

侧贴碳纤维布加固连续梁非线性有限元分析

为研究不同初始荷载作用下侧贴碳纤维布及侧贴预应力碳纤维布加固钢筋混凝土连续梁的加固效果,采用有限元分析软件ABAQUS对其进行数值模拟,并将有限元分析结果与试验结果对比。有限元分析表明：钢筋混凝土连续梁的加固效果受初始荷载的影响,初始荷载越小,加固效果越好;对纵向侧贴碳纤维布施加预应力,能够大幅提高钢筋混凝土连续梁的抗弯承载力,与未加固梁相比其抗弯承载力提高了65%以上;有限元计算结果与试验结果的荷载-挠度曲线吻合较好,两者的抗弯承载力相差不超过10%。所得结果可以为类似加固设计和试验提供参考。     

Optimization of process parameters of the activated tungsten inert gas welding for aspect ratio of UNS S32205 duplex stainless steel welds

The activated TIG (ATIG) welding process mainly focuses on increasing the depth of penetration and the reduction in the width of weld bead has not been paid much attention. The shape of a weld in terms of its width-to-depth ratio known as aspect ratio has a marked influence on its solidification cracking tendency. The major influencing ATIG welding parameters, such as electrode gap, travel speed, current and voltage, that aid in controlling the aspect ratio of DSS joints, must be optimized to obtain desirable aspect ratio for DSS joints. Hence in this study, the above parameters of ATIG welding for aspect ratio of ASTM/UNS S32205 DSS welds are optimized by using Taguchi orthogonal array (OA) experimental design and other statistical tools such as Analysis of Variance (ANOVA) and Pooled ANOVA techniques. The optimum process parameters are found to be 1 mm electrode gap, 130 mm/min travel speed, 140 A current and 12 V voltage. The aspect ratio and the ferrite content for the DSS joints fabricated using the optimized ATIG parameters are found to be well within the acceptable range and there is no macroscopically evident solidification cracking.     

一种鱼雷自导信号频率检测方法研究

靶场在进行智能鱼雷鉴定试验任务时,实时准确地检测出鱼雷自导信号的频率成分是靶标信号处理中的重要环节,谱线比值法便是靶标进行信号处理时检测信号频率的一种有效方法。本文介绍了谱线比值法的基本原理,针对目前鱼雷自导信号特点,对该方法提出了改进方案并进行了仿真。仿真结果表明,经改进的谱线比值法能够满足靶标检测复杂鱼雷自导信号体制下信号频率的使用要求。